|
 |
|
LPR
Gunsmithing has started to perform a number of special services on Schmidt Rubin K31 Rifles. We are also selling semi-finished, semi-inletted target stocks for the K31. Below is a basic description of these services, prices, and a few pictures of rifles and stocks that we have built. We hope that this page will help you understand the work we perform on these rifles. If you have any questions please contact us by email or phone. |
||
Rebarreled
Swiss K31 Rifles |
||
The links below
contain pictures of two K31s rebarreled by LPR |
||
Barrel
Work |
|||
Because
of the complex angles and cuts at the breech end of the K31 barrel,
a bushing must be made from the old barrel in order to fit the
new barrel. This adds an additional $100.00 to the initial rebarreling
of the rifle. This is a one-time cost and does not have to be
repeated for any subsequent rebarreling. |
|||
| Prices |
|||||
| Convert original barrel to accept replacement barrel | $110.00 | ||||
| Install Customer's Barrel | $230.00 | ||||
| All
barrels must have minimum breech diameter of 1.100” and
have a straight section 2.500 long or longer at the breech end to be used as a replacement barrel. |
|||||
In
House Barrels: |
Krieger Stainless (28" or less) | $570.00 | |||
| Douglas Chrome Moly (26" of less) | $425.00 | ||||
| Adams & Bennett Chrome Moly | $323.00 | ||||
Barrel installation prices included all breech cuts |
|||||
| Contouring of Customer Barrels, Special Contours, and Drilling & Tapping are Extra | |||||
| See
Price Guide for cost of upgrades
to above barrels. |
|||||
Cartridge
Selection |
||
| Cartridges with a 308 Winchester diameter (0.475”) base work well in the K31. We have used 308 Winchester, or its variants, and they feed, extract, and eject correctly in the K31. When using these cases we suggest a small base full length sizing die to ease extraction. 284 Winchester or 30-284 using 7.5 Swiss brass are a good choice as well. |
||
| Stocks |
|||
| |
|||
| Semi-finished,
semi-inletted target stocks are available in walnut, cherry and
beech. Each stock is made from hand-selected wood by Doug Bellows
of Vermont. Because these stocks are semi-finished, semi-inletted
they require final finishing, inletting, and bedding by the owner.
This makes them a good choice for do-it-yourselfers. |
|||
| Semi-finished,
semi-inletted target stocks: |
$150.00 |
||
Sights
and Sight Bases |
|||||
LPR manufactures
RPA and Redfield type sight bases for the K31. Sights with extra
windage such as the RPA Trakker are recommended for use on these
rifles. Redfield type sights can be used but leave little windage
adjustment on the right side.
LPR have a limited supply
of converted Parker Hale PH5A receiver sights available with Sure-X
type aperture. These sights have plenty of windage and are a good
sight for the K31 for a reasonable price. |
|||||
| RPA or Redfield receiver sight base for K31: | $49.00 | ||||
| RPA base will except PH5A sight listed below | |||||
| Parker Hale PH5A sight; polished, re-blued and refitted: | $250.00 | ||||
| Parker Hale PH5A sight, refitted but not polished and re-blued: | $195.00 | ||||
Contact Information:
Larry@LPRGunSmith.com
Phone: (603) 357-0055
If you have any problems with this site please e-mail: webmaster@lprgunsmith.com